Large sand blasting machine also mean Sand blasting room, sand blasting chamber,sand blasting booth.
Our sand blasting room is a pit free air recovery structure, which is directly installed on the cement floor.The working floor of the house is about 380mm high from the ground.The shell is 50mm thick fireproof rock wool colored steel house.Rectangular tube frame in the middle,4mm wear-resistant rubber board hanging inside.
Hollow flat car bearing 5 tons, manually propelled (if the weight exceeds 5 tons,it will be pulled by the hoist).
Filter cartridge dust remover, chimney height 15 meters.
Sand blasting room show:
Sand blasting room advantage:
* Qingdao XINSA machinery manufacturing Co., Ltd,independent R&D design this pitless pneumatic recycling sand blasting room.the only one that owns this technology of pitless sandblasting room all over the word.
* Comparison of environmental protection pneumatic recovery sand blasting room's characteristics with mechanical recycling sand blasting room:
1.Low cost of integrated operation and energy saving.
Pneumatic recovery Sandblasting room mode with no transmission mechanism is adopted, and the failure rate is low and maintenance is free. Reduce the maintenance time of the shutdown, and reduce the loss caused by the shutdown and maintenance;
2.the honeycomb floor has a sand-back structure without digging pit, and the civil engineering cost and the construction period are greatly reduced;
3.The structure is simplified and the interlocking control can be used in each system control, which greatly improves the convenience of maintenance and repair.
4.The key wear parts are equipped with standard modules, which are easy to maintain and replace, thus avoiding heavy maintenance work.
5.The sandblasting chamber adopts the upper supplementary air, the lower part and the side part can carry on the dust suppression circulation mode. The dust always drains downward, the visibility in the room is high, the working environment is good, the quality and efficiency of sand blasting are guaranteed, and the physical and mental health of the workers is protected.
6.The whole sand absorbing floor can recover all the sand materials in an instant, and there is no residual sand material on the ground. The sand blasting room is clean and clean in the room, no manual cleaning is required, and the working time is saved. Pneumatic pipe back sand, abrasive recovery up to 99, easy to clean the abrasive. Traditional mechanical recovery (or scrape floor) sandblasting room is almost impossible to thoroughly clean and replace abrasives.
7.The body of sandblasting room is simple and beautiful, and the installation is convenient and flexible.
8.The whole technical performance of sandblasting room is advanced, dust emission meets and is lower than the national and local environmental protection requirements, and the environmental pollution is completely eliminated.
Sand blasting room's technical parameters:
Sand blasting room's application case:
Related products:
Our workshop:
Our packing details:
Our transport details:
Our company:
According to your requirements, the most suitable machine will be designed for your workpieces, please indicate the following details.
1. What kind of workpiece you clean?
2. The workpiece size, length, width, height and weight of maximum workpiece.
3. What's your production capacity per day (8 hours)?
4. It's my pleasure if you can provide details workpiece photos to us.
Based on these details information, the detailed technical proposals will be sent to you for reference.
FAQ:
After-sale service:
1. Installation and commissioning issue: We will send one technicians to assist with machine installation and commissioning, customer pays for return tickets, hotel and diet. Customer need arrange skilled worker and prepare various installation machinery and tools.
2. Warranty time:12 months from date of commissioning completion, but no more than 18 months from date of delivery.
3. Supply full english documents: including general installation drawings, pit design drawings, manual book, electric wiring diagram, electric manual book and maintenance book, etc.
4. Our shot blasting spare parts are high quality with Cr20S High Chrome, ZGMn13, Mn65, etc.
Trade Information:
Trade term: FOB Qingdao China,(Sea freight and installation and debugging fee are not included).
MOQ:1 set.
Payment Term:30% Prepaid Contract Amounts or L/C.
After-Sales Service Provided:Engineers Available to Service Machinery Overseas.
Warranty time:one year.
Delivery time:About 20~30 days according the equipment's size.
Inspection certificate:Together with the equipment when delivery.
Any question pls kindly contact with us and welcome to visit our factory!
Qingdao Xinsa Machinery Manufacturing Co.,Ltd.
Sale manager:Alina
Tel:86-532-84126287
Fax:86-532-88138103
Cell:86-18563913196
http://qdxinsa.en.made-in-china.com/
REMARK:
We also can design and manufacture all kind of non-standard sand blasting chamber /room according to customer's different workpiece detail requirement,weight and productivity.
Our sand blasting room is a pit free air recovery structure, which is directly installed on the cement floor.The working floor of the house is about 380mm high from the ground.The shell is 50mm thick fireproof rock wool colored steel house.Rectangular tube frame in the middle,4mm wear-resistant rubber board hanging inside.
Hollow flat car bearing 5 tons, manually propelled (if the weight exceeds 5 tons,it will be pulled by the hoist).
Filter cartridge dust remover, chimney height 15 meters.
Sand blasting room show:
Sand blasting room advantage:
* Qingdao XINSA machinery manufacturing Co., Ltd,independent R&D design this pitless pneumatic recycling sand blasting room.the only one that owns this technology of pitless sandblasting room all over the word.
* Comparison of environmental protection pneumatic recovery sand blasting room's characteristics with mechanical recycling sand blasting room:
1.Low cost of integrated operation and energy saving.
Pneumatic recovery Sandblasting room mode with no transmission mechanism is adopted, and the failure rate is low and maintenance is free. Reduce the maintenance time of the shutdown, and reduce the loss caused by the shutdown and maintenance;
2.the honeycomb floor has a sand-back structure without digging pit, and the civil engineering cost and the construction period are greatly reduced;
3.The structure is simplified and the interlocking control can be used in each system control, which greatly improves the convenience of maintenance and repair.
4.The key wear parts are equipped with standard modules, which are easy to maintain and replace, thus avoiding heavy maintenance work.
5.The sandblasting chamber adopts the upper supplementary air, the lower part and the side part can carry on the dust suppression circulation mode. The dust always drains downward, the visibility in the room is high, the working environment is good, the quality and efficiency of sand blasting are guaranteed, and the physical and mental health of the workers is protected.
6.The whole sand absorbing floor can recover all the sand materials in an instant, and there is no residual sand material on the ground. The sand blasting room is clean and clean in the room, no manual cleaning is required, and the working time is saved. Pneumatic pipe back sand, abrasive recovery up to 99, easy to clean the abrasive. Traditional mechanical recovery (or scrape floor) sandblasting room is almost impossible to thoroughly clean and replace abrasives.
7.The body of sandblasting room is simple and beautiful, and the installation is convenient and flexible.
8.The whole technical performance of sandblasting room is advanced, dust emission meets and is lower than the national and local environmental protection requirements, and the environmental pollution is completely eliminated.
Sand blasting room's technical parameters:
| Item | Unit | Numerical value | |||
| Inner measurement of sand blasting room | length×Width×height | mm | 18000*7000*6000 | ||
| Sand blasting door dimensions | Width×height | mm | 3000*3000 | ||
| Cleaning workpiece speed | External surface of profiled structural parts | sq.m./h | 20-30(A-D grade according the different cleaning requirements of original Surface material and workpiece | ||
| cleaning quality rank | reach Sa2 .5 rank | ||||
| Processing material and strength range | Q235/Q345/65Mn/HT/ZG etc. | ||||
| surface roughness | μ | 40~75 depend on the shot ball's size. | |||
| Total power | kw | about 56.5 | |||
| Compressed air consumption | m³/min | 6,each spraying gun need 5 m³/min,protecting air-condition and the back flush dust cleaning need 1 m³/min | |||
| Compressed air pressure | MPa | 0.5-0.7 | |||
| facility adaptive temperature | Suitable for local four seasons normal temperature | ||||
| Control system | electrical appliance control system | Manual button control | |||
| Ground pit requirement | Can have no pit, waterproof | ||||
| overall noise | DB | ≤95 | |||
| dust discharge concentration | /m3 | 80mg/m3excel the 80mg/m3 of the GB16297-1996<emission standard of air pollutants> | |||
| dust content in the air after cleaned | mg/m3 | 10 | |||
Sand blasting room's application case:
Related products:
Our workshop:
Our packing details:
Our transport details:
Our company:
According to your requirements, the most suitable machine will be designed for your workpieces, please indicate the following details.
1. What kind of workpiece you clean?
2. The workpiece size, length, width, height and weight of maximum workpiece.
3. What's your production capacity per day (8 hours)?
4. It's my pleasure if you can provide details workpiece photos to us.
Based on these details information, the detailed technical proposals will be sent to you for reference.
FAQ:
After-sale service:
1. Installation and commissioning issue: We will send one technicians to assist with machine installation and commissioning, customer pays for return tickets, hotel and diet. Customer need arrange skilled worker and prepare various installation machinery and tools.
2. Warranty time:12 months from date of commissioning completion, but no more than 18 months from date of delivery.
3. Supply full english documents: including general installation drawings, pit design drawings, manual book, electric wiring diagram, electric manual book and maintenance book, etc.
4. Our shot blasting spare parts are high quality with Cr20S High Chrome, ZGMn13, Mn65, etc.
Trade Information:
Trade term: FOB Qingdao China,(Sea freight and installation and debugging fee are not included).
MOQ:1 set.
Payment Term:30% Prepaid Contract Amounts or L/C.
After-Sales Service Provided:Engineers Available to Service Machinery Overseas.
Warranty time:one year.
Delivery time:About 20~30 days according the equipment's size.
Inspection certificate:Together with the equipment when delivery.
Any question pls kindly contact with us and welcome to visit our factory!
Qingdao Xinsa Machinery Manufacturing Co.,Ltd.
Sale manager:Alina
Tel:86-532-84126287
Fax:86-532-88138103
Cell:86-18563913196
http://qdxinsa.en.made-in-china.com/
REMARK:
We also can design and manufacture all kind of non-standard sand blasting chamber /room according to customer's different workpiece detail requirement,weight and productivity.